How To Set Up A Dish Network Remote To Tv

Dish Network Dish Installation steps

Installation Considerations

While all DISH Network satellite receivers can be connected to the DISH 1000.ii, the following models
may non observe and will not support the 129°W location: 1000, 2000, 3000, 4000, 5000, JVC-DVHS (IRR),
and the DishPlayer 7100/7200.

This installation supports Legacy receivers, but there must be at least ane DISH Pro or DISH Pro Plus
receiver in the installation. Legacy receivers are receivers which practice not have the DISH Pro or DISH Pro
Plus logo (shown below).

About the System

The DISH Pro Plus 1000.2 LNBF provides reception from the 110°W, 119°W, and 129°W orbital locations, and provides an LNBF input port to receive programming from another satellite. The post-obit LNBF types can be continued to the LNBF input port: DISH Pro Unmarried, DISH Pro Dual, or DISH Network bandstacked LNBFs.

The LNBF assembly supports connectedness of upward to 3 satellite receivers in whatsoever of the following
combinations:

• Single-cablevision connection to DISH Pro Plus (dual-tuner) receivers, when each input is used with a DISH Pro Plus Separator.
• Single-cablevision connection to DISH Pro receivers.
• Single-cable connection to a Legacy receiver provided that a DISH Pro or DISH Pro Plus receiver is also connected and powered at all times. No DISH Pro Adapter is required.

Effigy 1. DISH 1000.ii Antenna Installation Overview

ane. Find Azimuth/Elevation/Skew angles for your location
2. Find a location for the dish antenna with a articulate line of sight and a sturdy mounting surface
3. Mount the mast, making sure it is admittedly vertical
4. Assemble the dish antenna, setting the skew and elevation angles in the process. Use additional skew bolts for skew angles greater than 110 or less than 70
5. Mount the dish antenna on the mast and bespeak the dish to the azimuth angle
half dozen. Run cables betwixt the dish antenna and the receiver(s), leaving a service loop around the Mast Clamp
7. Using a peaking meter attached to the DPP 1000.2 LNBF PORT 1, acme the dish on 119°W using transponder xi or higher for maximum strength. Tighten all bolts (meet Table 1) and re-confirm maximum signal
Note: The 1000.2 Three-LNBF Bracket with 3 DP Dual (or DP Single) LNBFs can be used in place of the Integrated Adapter Bracket and DPP 1000.ii LNBF.
8. Connect the receiver cablevision(southward) to the DPP yard.2 LNBF PORT 1 (and PORT 2 and PORT 3, as necessary) and receiver. Some restrictions apply when connecting Legacy receivers.
nine. Run Check Switch test and confirm 110°W, 119°W, and 129°W reception
ten. Take a software download, if you didn't already
11. Run a Check Switch exam and confirm 110ºW, 119ºW, 129° reception
12. Install additional receiver(s), if necessary
13. If applicable, connect a 2d satellite dish to the DPP k.2 LNBF'southward LNB IN port

Assembling and Mounting the Dish

Follow these instructions to assemble the satellite dish, mount it, and signal it in the direction of the
satellites.

• Using the azimuth and elevation angles, find a location for the satellite dish where it can exist pointed towards the satellites located at these angles. Make sure nothing blocks the line of sight between the dish and the satellites.
• Mount the mast to a solid surface so that the dish antenna cannot move or be bumped out of alignment. Keep in mind that physical and environmental conditions can cake your satellite dish's power to receive a clear satellite bespeak. Never mount to a tree or a public utility pole.
• Align the top function of the mast so that it is admittedly vertical. If the height function of the mast is off vertical by only a few degrees, it volition be difficult or maybe even impossible for you to find the satellites. Take at least two readings with a level, on the upper mast, that are ninety degrees autonomously from one another.
• Loosen both skew bolts and gear up the skew by rotating the dish mounting bracket to align the marker with the required angle on the skew scale which you lot wrote above. Tighten the skew bolts deeply. Come across Table i for the required torque values. Afterwards the skew is set, do non try to finetune the skew angle when aiming the dish.

Annotation: If your skew bending is at the extreme ends of the calibration (greater than 110 or less than lxx),
insert nuts and bolts from the hardware pack into the additional skew holes. These additional
skew holes provide greater stability to the dish at these extreme angles. See Effigy 2.

Installing the Receivers

Employ the steps beneath while referring to Figure ane.

1. Run RG-six coaxial cables from the DISH k.2 antenna to the receiver location(s) using the following cable requirements. Grounding, other devices, and in-home cabling must as well come across these requirements.

• RG-half-dozen coaxial cable rated for at to the lowest degree 950 to 2150 MHz must exist used in this installation. Do non use existing cables such every bit RG-59 as it may cause signal loss. Likewise, be sure that whatsoever outdoor connections are made using waterproof F-connectors rated for 2150 MHz or greater.
• The length of the RG-half-dozen cable from whatever receiver and farthest dish connected in the system must not be longer than:
  - 200 feet for DISH Pro or DISH Pro Plus receivers.
  - 100 feet for Legacy receivers.
• The cable length betwixt the DISH 1000.ii and a connected compatible LNBF must be 80 feet or less.
  -The cablevision's heart conductor must not extend past the rim of the F-connector more than the thickness of a nickel.
  -Tighten all outdoor cable connections up to the torque values recommended by the manufacturer to ensure seal against wet. Harm caused by over-tightening is not covered past the express warranty. Tighten all indoor coaxial cablevision connections to the receiver only past paw. If you employ a wrench, you may over-tighten the connections and damage your equipment.

1. Connect a temporary cable to a peaking meter. Thread the other terminate of the cable through the LNBF arm and bracket. Connect the temporary cable to PORT 1 of the DPP 1000.2 LNBF and attach the LNBF to the bracket with ii screws. If using the Three-LNBF bracket and 3 DP Dual (or DP Single) LNBFs, connect the temporary cablevision from the peaking meter to the 119°Due west (center) LNBF. Adhere the LNBFs to the subclass using the included screws.
   - Note: If the peaking meter does not produce at least 600 mA to power the DPP 1000.2 LNBF, connect PORT two of the LNBF to the SATELLITE IN port of a powered receiver, or temporarily connect the Three-LNBF bracket with a Dual or Single LNBF for peaking on 119°W.
2. Peak the dish for the strongest possible signal on the 119°W satellite signal using the azimuth and elevation settings y'all wrote on page 3. Do not adjust the skew.
   - Note: If you lot cannot detect the 119°West point, try adjusting the elevation up or down one or two degrees. Ensure you lot are peaking the dish using transponder 11 or higher.
3. With the peaking meter nonetheless continued, tighten the mast clench and elevation bolts using the torque values listed in Tabular array 1 on page 6. Re-ostend signal strength later tightening the bolts.
4. Remove the temporary cable used for peaking the dish. Thread the cable(s) from the receiver(s) through the LNBF arm and subclass. Connect these cables to PORT one, PORT 2 and PORT 3, as applicative.
   - Notation: If using the 3-LNBF Bracket with DP Dual (or DP Single) LNBFs, refer to the section
   Connecting to a Switch on page 9 and the switch'south installation instructions for additional details.
5. Connect a cablevision from DPP yard.2 LNBF PORT i (or PORT 2 or PORT 3) to a DISH Pro or DISH Pro Plus (dual-tuner) satellite receiver's SATELLITE IN connection(s). If a Legacy receiver is present, it should be installed concluding.
6. To connect DISH Pro Plus (dual-tuner) receivers with a single cable, install a DISH Pro Plus Separator equally follows:
   a. Connect a cable from the DPP 1000.2 LNBF output (PORT i, PORT ii, or PORT iii) to the DISH Pro Plus Separator Input.
   b. Connect cables betwixt the receiver'south SATELLITE IN 1 and SATELLITE IN 2 to SATELLITE IN i and SATELLITE IN 2 respectively on the DISH Pro Plus Separator.
   - You must use a DISH Pro Plus Separator in a single-cable/dualtuner receiver installation. A splitter or other device will not work in this configuration.
   - Tighten all indoor coaxial cable connections to the receiver only past hand. If yous utilise a wrench, you lot may over-tighten the connections and damage your equipment
7. Connect the receiver(south) to the TV(s) and display the Point Dish screen (if not shown, for most
   receivers, press MENU-6-1-1 on the remote control).

8. From the Point Dish screen, run Check Switch. On Legacy receiver models 2800, 3900, 4900, and 6000, select the SuperDISH Installation-3Sat option prior to running the Check Switch test. On all other Legacy models, select Examination. When the Check Switch procedure finishes, you should see an Installation Summary screen similar to the ones shown below. Brand sure the summary screen shows reception from the 119°W, 110°W, and 129°W satellites on all available satellite tuners. Also confirm the LNBF is correctly identified every bit a DPP m.2 (mill software on some models may place this LNBF as a DPP Twin or DPP Triple, which is OK). Legacy receivers volition identify the LNBF as SW64.

   - Note: On some models, you might not run into signal from 129°W until afterwards yous take a software
   download and run a Check Switch in steps ten and 11. Legacy receiver models g, 2000, 3000,
   4000, 5000, 7100, 7200, and JVC-DVHS (IRR) may not observe and will non support the 129°W
   location.
   No- te: If you are using the Iii-LNBF Bracket, your Installation Summary screen will vary
   depending on the connected switch. Make sure the summary screen shows reception from the
   119°Due west, 110°W, and 129°Westward satellites on all available satellite tuners.

9. Leave the Installation Summary screen to display the Point Dish/Bespeak screen. Make sure the betoken strength bar is green and locked for the 119°Westward, 110°West, and 129°W satellites.
   - Note: Y'all might not encounter signal from 129°W until after you take a software download and run a Check Switch in steps 10 and eleven.

10. Leave the Point Dish/Indicate screen and follow the on-screen instructions for taking a receiver software download. Do not disturb the receiver during the process of downloading software. If exiting the Bespeak Dish screen does not start the download process, turn off the receiver for at least 20 minutes (on most receivers) to let the receiver to take a software download.

11. Run Check Switch again and ostend reception for all three satellites on all available satellite tuners. Your Installation Summary screen should be like to the ones shown above in step 8. Some software on some models may identify the DPP 1000.2 LNBF every bit a DPP 1K.2. This identification is OK.

12. If installing an additional receiver, follow steps six-11. Make sure the summary screen shows reception from the 110°West, 119°Westward, and 129°W satellites. Keep in mind that a DISH Pro or DISH Pro Plus receiver must remain connected and powered at all times to power the DPP thou.ii LNBF.

How To Set Up A Dish Network Remote To Tv,

Source: https://www.satpro.tv/dish-network-dish-installation-steps.aspx

Posted by: minickinectow.blogspot.com

Share this post